We will not share any of your information.
If you find any of the following information helpful, please click on the button below to receive blog update notices via email. Electronics (Stereo, TV, Computers, etc.).Will be the same for DPMS High or Low.Ī2 handguard will be the same as AR15 assuming the length is the same.Ĭarry handle, milsurp from eBay or a Stag blem are probably your cheapest sources lately. Standard barrel nut, weld spring, and delta ring.
Handguard cap, fits between gas block and barrel shoulder, same as AR15. Im going to add a red dot later so i want something Im. Need a rear sight that would be compatible with the front A2 front post besides the A2 carry handle.
You’ll need to get the screw holes on it tapped per their manual in order to set it up, which isn’t hard to do, but I don’t know why JP doesn’t do it for you. Compatible rear sights with the A2 front sight base Centerfire Rifles - Semiautomatic or Gas Operated. The JP does have clamping screws which work better than I expected, but at some point I’m going to have Adco pin it to the barrel for a little bit more security. Please scroll down to view products we carry for this platform or click on one of the links below. Click on any part number highlighted in RED to view specific details or to purchase online.
We carry AR-15 uppers, magazines, stocks and handguards, sights, mounts, rails, tools, and AR-15 parts. I actually have used that JP sight/gas block on a ‘sleeper’ AR15 and had zero trouble with it, although gas pressures on an AR15 will of course be a lot less than an AR10, but in the way I’ve got it configured it’s probably the softest shooting AR I own. Midwest Gun Works is proud to offer a wide assortment of parts and accessories for the AR-15 Platform. An A2 carry handle should fit it fine in that case. That said, I’d sooner get a DPMS Low upper to mate to that lower for that reason if A2 style is the goal. Since the gas block is AR15 height, that’s a problem. This may be useful, I recall going out and getting the numbers on rail height at the time:ĭPMS Low is same height as AR15, DPMS High is higher. The UTG Super Slim Fixed Rear Sight is precision machined from aircraft aluminum with a matte black finish and features a standard A2 front sight assembly.
The 733 series uses an upper receiver with fixed carry handle and iron sights. Detachable carry handle for use with AR-15 flat top rifles, attaches and detaches quickly to any picatinny rail equipped rifle. If by 'carry handle' you mean a detachable carry handle mounted to a flattop upper, then the F-Marked FSB is what you need. More broadly, has anyone done a similar "LR308 A2 Classic" style build?Īny information you can provide is helpful. It includes a Rifle Handguard, A2 front sight, an M4 flat-top forged upper receiver with forwarding assist, a BCA Bolt Carrier Group with billet extractors, a Flash Hider, and a Charging Handle. If by 'carry handle' you mean an A1/A2 upper receiver with an integral carry handle/sight, then the standard FSB is what you need. The height limitation is why the detachable carry handle sight is limited to 600m versus 800m for the A2. 750 adjustable A2 Front Sight Block, which seems like it should fit my barrel:ĭoes anyone know of any A2 hand guards or A2 carry handles which would fit a DPMS high profile build / would align and fit well with the JP Enterprises Front Sight Block linked above? 040' taller front sight post is a band-aid to allow use of a non-F-marked FSB equipped barrel with a flattop upper receiver and a MIL-Spec height rear sight. I have found one (relatively expensive) source for a. A2 Detachable Carry Handle 79. In general, I am looking to recreate a DPMS Classic ( ), including an A2 carry handle, A2 Front Sight Block and A2 hand guard.Īero Precision M5 Upper Receiver (not the M5E1)īallistic Advantage 20".